If you have been reading about aseptic technique and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2025-11-01. Where a claim depends on a specific study, the study is described rather than over-claimed.
Quality control relies on analytical methods that detect changes in purity, identity, and concentration. Reverse-phase high-performance liquid chromatography separates the parent peptide from degradation products, while mass spectrometry confirms molecular mass. Water content can be measured by Karl Fischer titration, and amino acid analysis or peptide mapping may reveal sequence-level modifications. Stability studies compare stored samples against baseline material at defined intervals. Documentation should link each result to a lot number, storage condition, and test date so that trends can be reviewed.
Receipt and inventory practices begin with inspection of packaging, temperature indicators, and lot-specific documentation. A certificate of analysis typically reports purity, identity, and sometimes residual water or counterion content. Containers should be labeled with the peptide name, lot number, date received, and storage location. Before a sealed vial is opened, it is often equilibrated to room temperature to reduce condensation on the contents. Clean tools, gloves, and a designated workspace limit contamination and accidental adsorption losses.
Reconstitution is a critical handling step. The appropriate solvent—often sterile water, phosphate-buffered saline, or a water-acetonitrile mixture—is chosen based on peptide solubility. Adding solvent gently down the vial wall and swirling, rather than vortexing, reduces foaming and shear stress. The resulting solution should be clear; visible particles indicate incomplete dissolution or contamination. Concentration is recorded accurately because it affects subsequent use. If the peptide is not fully soluble, a small amount of organic solvent or a different buffer may be required, but this changes the final composition.
After reconstitution, solutions are divided into single-use aliquots and stored at -80°C. Labels include peptide name, concentration, buffer composition, date, and lot number. Freeze-thaw cycles are minimized by thawing only the needed aliquot on ice or at room temperature. Some peptides benefit from the addition of a carrier protein, such as bovine serum albumin, or a cryoprotectant like glycerol to reduce adsorption to plastic. Glass vials with low-binding surfaces are preferred for dilute solutions. Shipping of frozen aliquots uses dry ice and insulated containers to maintain the cold chain.
Receiving a peptide shipment requires immediate inspection of the packaging and temperature indicators. Any deviation from the specified cold chain should be documented and investigated. Upon arrival, solid peptides are generally kept at -20°C, whereas liquid formulations are stored at -80°C. Vials should be kept upright and protected from light. Repeated warming and cooling of the entire container is avoided by preparing smaller working aliquots. A log of lot numbers, receipt dates, and storage locations supports traceability and quality control.
| Property | Value | Notes |
|---|---|---|
| Common synonyms | Peptide, oligopeptide, polypeptide | Usage varies; polypeptide often implies a longer chain |
| Purity assessment | High-performance liquid chromatography | Often reversed-phase; reported as area percent with method and wavelength stated |
| Identity confirmation | Mass spectrometry | Observed mass compared with theoretical mass within instrument tolerance |
| Water content (lyophilized) | Karl Fischer titration | Residual moisture can affect stability and weighing accuracy |
| Container compatibility | Low-binding polypropylene | Glass may adsorb some peptides; plastic additives can leach |
Peptide handling begins with careful receipt and inventory. Containers should be inspected for damage, label information should match the certificate of analysis, and storage location should be recorded. Many lyophilized peptides are electrostatic and may cling to vial walls or weighing paper, which can complicate transfer. Allowing a cold vial to equilibrate to room temperature before opening reduces condensation on the contents. Clean tools, gloves, and a low-humidity workspace limit contamination and moisture exposure during manipulation.
Reconstitution is the process of dissolving a dried peptide in a suitable solvent. The choice of solvent depends on solubility, charge, and sequence; sterile water is common, while buffers or small amounts of organic solvent may be needed for hydrophobic peptides. Adding solvent gently down the vial wall and mixing by inversion or gentle swirling reduces foaming and shear. Vortexing or vigorous pipetting can denature some peptides or promote aggregation. The resulting solution should be visually inspected for particles, turbidity, and complete dissolution before use.
Receiving a peptide begins with recording its identity, lot number, quantity, and arrival condition. Dry material is often kept in sealed containers with desiccant and an inert headspace to limit moisture and oxygen. Containers should be compatible with the peptide and solvent; some peptides adsorb to certain plastics or glass. Labels should include date, concentration, solvent, and storage location. A centralized inventory with temperature logs helps prevent loss and mix-ups.
Reconstitution involves adding a solvent to dry peptide, often water or a buffered solution. The chosen liquid should match the peptide's solubility and intended assay, and it should be free of contaminants. Gentle mixing or inversion reduces foaming and shear, which can damage some peptides. If the peptide does not dissolve readily, adjusting pH or using a small amount of organic co-solvent may help. The final solution is typically clarified before use in analytical or laboratory procedures.
After reconstitution, solutions are usually divided into single-use aliquots to limit repeated handling. Each aliquot is stored at a temperature appropriate for the peptide, with -20 °C or -80 °C common for longer-term laboratory storage. Freeze-thaw cycles are minimized because they can cause aggregation, precipitation, or loss of activity. Temperature monitoring and documented storage conditions support reproducibility across experiments. When a peptide is removed from storage, it is typically allowed to equilibrate before opening to reduce condensation.
The mechanism of action of biguanides is not fully understood, and many mechanisms have been proposed for metformin. Biguanides do not affect the output of insulin, unlike other hypoglycemic agents such as sulfonylureas and meglitinides. Therefore, they are effective in Type 2 diabetics; and in Type 1 diabetes when used in conjunction with insulin therapy. Mainly used in Type II diabetes, metformin is considered to increase insulin sensitivity in vivo, resulting in reduced plasma glucose concentrations, increased glucose uptake, and decreased gluconeogenesis. However, in hyperinsulinemia, biguanides can lower fasting levels of insulin in plasma. Their therapeutic uses derive from their tendency to reduce gluconeogenesis in the liver, and, as a result, reduce the level of glucose in the blood. Biguanides also tend to make the cells of the body more willing to absorb glucose already present in the bloodstream, and there again reducing the level of glucose in the plasma. Biguanides have been shown to interact with copper, specifically in mitochondria, where they interfere with cell metabolism by chelating Copper in its 2+ oxidation state (Cu(II)).
Cell membranes contain a variety of biological molecules, notably lipids and proteins. Composition is not set, but constantly changing for fluidity and changes in the environment, even fluctuating during different stages of cell development. Specifically, the amount of cholesterol in human primary neuron cell membrane changes, and this change in composition affects fluidity throughout development stages. Material is incorporated into the membrane, or deleted from it, by a variety of mechanisms:
Weak affinity chromatography (WAC) is an affinity chromatography technique for affinity screening in drug development. WAC is an affinity-based liquid chromatographic technique that separates chemical compounds based on their different weak affinities to an immobilized target. The higher affinity a compound has towards the target, the longer it remains in the separation unit, and this will be expressed as a longer retention time. The affinity measure and ranking of affinity can be achieved by processing the obtained retention times of analyzed compounds. Affinity chromatography is part of a larger suite of techniques used in chemoproteomics based drug target identification. The WAC technology is demonstrated against a number of different protein targets – proteases, kinases, chaperones and protein–protein interaction (PPI) targets. WAC has been shown to be more effective than established methods for fragment based screening. Affinity chromatography was conceived and first developed by Pedro Cuatrecasas and Meir Wilchek.
The full-length human protein comprises 2,843 amino acids with a (predicted) molecular mass of 311646 Da. Several N-terminal domains have been structurally elucidated in unique atomistic high-resolution complex structures. Most of the protein is predicted to be intrinsically disordered. It is not known if this large predicted unstructured region from amino acid 800 to 2843 persists in vivo or would form stabilised complexes – possibly with yet unidentified interacting proteins. Recently, it has been experimentally confirmed that the mutation cluster region around the center of APC is intrinsically disordered in vitro.
Sources: en.wikipedia.org
The first definition of the term bioinformatics was coined by Paulien Hogeweg and Ben Hesper in 1970, to refer to the study of information processes in biotic systems. This definition placed bioinformatics as a field parallel to biochemistry (the study of chemical processes in biological systems). Bioinformatics and computational biology involved the analysis of biological data, particularly DNA, RNA, and protein sequences. The field of bioinformatics experienced explosive growth starting in the mid-1990s, driven largely by the Human Genome Project and by rapid advances in DNA sequencing technology. Analyzing biological data to produce meaningful information involves writing and running software programs that use algorithms from graph theory, artificial intelligence, soft computing, data mining, image processing, and computer simulation. The algorithms in turn depend on theoretical foundations such as discrete mathematics, control theory, system theory, information theory, and statistics.
Apamin is an 18 amino acid globular peptide neurotoxin found in apitoxin (bee venom). Dry bee venom consists of 2–3% of apamin. Apamin selectively blocks SK channels, a type of Ca2+-activated K+ channel expressed in the central nervous system. Toxicity is caused by only a few amino acids, in particular cysteine1, lysine4, arginine13, arginine14 and histidine18. These amino acids are involved in the binding of apamin to the Ca2+-activated K+ channel. Due to its specificity for SK channels, apamin is used as a drug in biomedical research to study the electrical properties of SK channels and their role in the afterhyperpolarizations occurring immediately following an action potential.
In the competition of bacterial cells and host cells with the antimicrobial peptides, antimicrobial peptides will preferentially interact with the bacterial cell to the mammalian cells, which enables them to kill microorganisms without being significantly toxic to mammalian cells. With regard to cancer cells, they themselves also secrete human antimicrobial peptides including defensin, and in some cases, they are reported to be more resistant than the surrounding normal cells. Therefore, we cannot conclude that selectivity is always high against cancer cells.
Sources: en.wikipedia.org
Allow the sealed vial to equilibrate to room temperature so condensation does not form on the powder or solution. Wipe the exterior with a suitable disinfectant if the workspace requires it. Open the vial in a clean, draft-free area to reduce contamination.
Vortexing creates rapid air-liquid interfaces that can cause foaming and promote aggregation. Gentle inversion or slow swirling usually dissolves the peptide with less physical stress. Some sequences tolerate vortexing, but minimizing shear is a general precaution.
A certificate of analysis usually reports purity by HPLC, identity by mass spectrometry, appearance, and sometimes water content or counterion. It may also list lot number, storage recommendations, and handling notes. Exact content varies by supplier and product type.
Common solvents include sterile water, phosphate-buffered saline, and water-acetonitrile mixtures. The choice depends on the peptide's solubility profile and the buffer compatibility for the intended application. Manufacturers often provide a recommended solvent on the product information sheet.